| JaLCDOI | 10.18926/14058 |
|---|---|
| FullText URL | Mem_Fac_Eng_OU_42_44.pdf |
| Author | Ogawa Takafumi| Tsuruta, Kenji| Totsuji, Chieko| Totsuji, Hiroo| Hiroshi Iyetomi| |
| Abstract | To analyze vibrational properties of Si crystal with a single charge-neutral vacancy, we perform large-scale simulations based on tight-binding molecular-dynamics method. Vibrational modes and frequencies are obtained by diagonalizing dynamical matrix within a harmonic approximation. Results indicate that there exist vibrational modes spatially localized around the vacancy and large frequency shifts associated with the localized modes contribute significantly to reduction of the vibrational free energy. |
| Publication Title | Memoirs of the Faculty of Engineering, Okayama University |
| Published Date | 2008-01 |
| Volume | volume42 |
| Issue | issue1 |
| Start Page | 44 |
| End Page | 47 |
| ISSN | 0475-0071 |
| language | 英語 |
| File Version | publisher |
| NAID | 120002308412 |
| JaLCDOI | 10.18926/14069 |
|---|---|
| FullText URL | Mem_Fac_Eng_OU_42_104.pdf |
| Author | Donghui, MA| Torii, Tashiyuki| Shimizu, Kenichi| Matsuba, Akira| |
| Abstract | As model specimens of surface film-bonded materials, pure copper films with a thickness of 100μm were bonded to the surface of steel base with epoxy resin, where the tensile residual stress was measured by an X-ray on the surface copper film. The distribution of initial electric resistance was measured on both copper film and base specimen by a direct current potential drop technique. As a result, there was a good agreement between the measured and theoretical values. From the fatigue testing results, it was shown that the measured electric resistance increased with the fatigue crack length on the copper film, which was almost equal to the theoretical value calculated for a central slit in a plate with finite width. This was probably because the fatigue crack was opened due to the tensile residual stress on the film even under unloading condition. In addition, the internal crack length during fatigue was examined by ultrasonic testing for the film-bonded specimen. As a result, there was a difference in the fatigue crack length between the surface copper film and the inner base. |
| Publication Title | Memoirs of the Faculty of Engineering, Okayama University |
| Published Date | 2008-01 |
| Volume | volume42 |
| Issue | issue1 |
| Start Page | 104 |
| End Page | 109 |
| ISSN | 0475-0071 |
| language | 英語 |
| File Version | publisher |
| NAID | 120002308537 |
| JaLCDOI | 10.18926/14061 |
|---|---|
| FullText URL | Mem_Fac_Eng_OU_42_56.pdf |
| Author | Miyake Takashi| Totsuji, Chieko| Nakanishi Kenta| Tsuruta, Kenji| Totsuji, Hiroo| |
| Abstract | We analyze the ground state of the two-dimensional quantum system of electrons confined in a parabolic potential with the system size around 100. We map the system onto a classical system on the basis of the classical-map hypernetted-chain (CHNC) method which has been proven to work in the integral-equation-based analyses of uniform unbounded systems and then apply classical numerical simulations. We find that the confined system undergoes the transition to the spin polarized state with the decrease of the average density and the corresponding critical value is as low as rs ∼ 0.3 in terms of the usual rs parameter estimated for the average density. As the ground state for given value of the rs parameter, our data give the critical value for the transition around 20 which is consistent with the known possibility. The advantage of our method is a direct applicability to geometrically complex systems which are difficult to analyze by integral equations. The application to the structure like quantum dots reported here is the first example of such applications. |
| Publication Title | Memoirs of the Faculty of Engineering, Okayama University |
| Published Date | 2008-01 |
| Volume | volume42 |
| Issue | issue1 |
| Start Page | 56 |
| End Page | 59 |
| ISSN | 0475-0071 |
| language | 英語 |
| File Version | publisher |
| NAID | 120002308633 |
| JaLCDOI | 10.18926/14071 |
|---|---|
| FullText URL | Mem_Fac_Eng_OU_42_110.pdf |
| Author | Nogami, Yasuyuki| Morikawa, Yoshitaka| |
| Abstract | This paper shows a method for checking the parity of (#Jc − 1)/2 without calculating the order #Jc, where #Jc is the order of genus 2 or 3 hyperelliptic curve. |
| Publication Title | Memoirs of the Faculty of Engineering, Okayama University |
| Published Date | 2008-01 |
| Volume | volume42 |
| Issue | issue1 |
| Start Page | 110 |
| End Page | 114 |
| ISSN | 0475-0071 |
| language | 英語 |
| File Version | publisher |
| NAID | 120002308489 |
| JaLCDOI | 10.18926/14057 |
|---|---|
| FullText URL | Mem_Fac_Eng_OU_42_36.pdf |
| Author | Kato, Hidehiro| Nekado, Kenta| Nogami, Yasuyuki| Morikawa, Yoshitaka| |
| Abstract | This paper proposes an exponentiation method with Frobenius mappings. Our method is closely related to so-called interleaving exponentiation. Different from the interleaving exponentiation methods, our method can carry out several exponentiations using same base at the same time. The efficiency to use Frobenius mappings for an exponentiation in extension field is well introduced by Avanzi and Mihailescu. This exponentiation method is based on so-called simultaneous exponentiation and uses many Frobenius mappings. Their method more decreased the number of multiplications; however, the number of Frobenius mappings inversely increased. Compared to their method , the number of multiplications needed for the proposed method becomes about 20% larger; however, that of Frobenius mappings becomes small enough. |
| Keywords | exponentiation Frobenius mapping extension field |
| Publication Title | Memoirs of the Faculty of Engineering, Okayama University |
| Published Date | 2008-01 |
| Volume | volume42 |
| Issue | issue1 |
| Start Page | 36 |
| End Page | 43 |
| ISSN | 0475-0071 |
| language | 英語 |
| File Version | publisher |
| NAID | 120002308105 |
| JaLCDOI | 10.18926/14065 |
|---|---|
| FullText URL | Mem_Fac_Eng_OU_42_91.pdf |
| Author | Ryohei, Hamana| Konishi, Masami| Imai, Jun| |
| Abstract | Various kind of productions are made in semiconductor fabrications, where it employs the production system with multiprocesses and multiple Automated Guided Vehicles(AGVs) for transportation. It is difficult to optimize planning of production and transportation simultaneously because of the complicated flow of semifinished products. This paper describes the formulations of production scheduling, transportation routing and sequence planning of material handling system, and algorithm for simultaneous optimization of plannings by using solution space reduction and simulated annealing method. In this paper, all production system is decomposed to the production scheduling problem, transportation routing problem by AGVs and sequence planning of material handling system with managing stockers and buffers. Production scheduling problem and transportation routing problem are solved by the optimization algorithm using the decomposition routing problem. Sequence planning of material handling robot problem is solved by the algorithm using simulated annealing method. |
| Publication Title | Memoirs of the Faculty of Engineering, Okayama University |
| Published Date | 2008-01 |
| Volume | volume42 |
| Issue | issue1 |
| Start Page | 91 |
| End Page | 103 |
| ISSN | 0475-0071 |
| language | 日本語 |
| File Version | publisher |
| NAID | 120002308279 |
| JaLCDOI | 10.18926/14064 |
|---|---|
| FullText URL | Mem_Fac_Eng_OU_42_79.pdf |
| Author | Notsu Tadafumi| Konishi, Masami| Imai, Jun| |
| Abstract | The operations of a reactor furnace such as a blast furnace still depend on the experiences and intuitions of skilled operators due to the complexity of internal furnace phenomena and high temperature. There is a great demand for stable operations under the circumstances of a decrease in the number of skilled operators and difficulty in technology inheritance. This paper aims to construct mathematical description for control of a reactor furnace. Further, the linear-quadratic-gaussian control system for a reactor furnace is proposed, which estimates inner furnace temperature distribution using measured data near furnace wall. Temperature distribution of a furnace is controlled based on the estimated inner temperature distribution changing of boundary conditions of a furnace. The practicability of the proposed control method was checked through numerical experiments. |
| Publication Title | Memoirs of the Faculty of Engineering, Okayama University |
| Published Date | 2008-01 |
| Volume | volume42 |
| Issue | issue1 |
| Start Page | 79 |
| End Page | 90 |
| ISSN | 0475-0071 |
| language | 英語 |
| File Version | publisher |
| NAID | 120002308624 |
| JaLCDOI | 10.18926/14063 |
|---|---|
| FullText URL | Mem_Fac_Eng_OU_42_71.pdf |
| Author | Kawase, Koichi| Konishi, Masami| Imai, Jun| |
| Abstract | In this research, Fuzzy control theory is applied to the inventory control of the supply chain between multiple companies. The proposed control method deals with the amount of inventories expressing supply chain between multiple companies. Referring past demand and tardiness, inventory amounts of raw materials are determined by Fuzzy inference. The method that an appropriate inventory control becomes possible optimizing fuzzy control gain by using SA method for Fuzzy control. The variation of uncertain demand is given to the proposal method. Furthermore, the method of forecasting demand and the effectiveness of fuzzy control method are confirmed by numerical experiments. As the results, the proposal method suppressed increase in an unnecessary cost when demand varies. |
| Publication Title | Memoirs of the Faculty of Engineering, Okayama University |
| Published Date | 2008-01 |
| Volume | volume42 |
| Issue | issue1 |
| Start Page | 71 |
| End Page | 78 |
| ISSN | 0475-0071 |
| language | 英語 |
| File Version | publisher |
| NAID | 120002308296 |
| JaLCDOI | 10.18926/14062 |
|---|---|
| FullText URL | Mem_Fac_Eng_OU_42_60.pdf |
| Author | Kikuchi, Junji| Konishi, Masami| Imai, Jun| |
| Abstract | In steel works, molten metals discharged from blast furnace are put into a pan for transportation called torpedo and transported to steel making factory by a locomotive. In molten metals transportation, it becomes issues to prevent temperature drop of molten metals for stable production of down stream plants to shorten transportation time. Therefore it is necessary to make an appropriate plan for molten metals transfer considering the production and the transportation simultaneously. In this paper, molten metals transfer planning method is proposed including production scheduling. That is, torpedo schedule, transfer request assignment and route plan of locomotives are optimized according to each objective. |
| Publication Title | Memoirs of the Faculty of Engineering, Okayama University |
| Published Date | 2008-01 |
| Volume | volume42 |
| Issue | issue1 |
| Start Page | 60 |
| End Page | 70 |
| ISSN | 0475-0071 |
| language | 英語 |
| File Version | publisher |
| NAID | 120002308612 |
| JaLCDOI | 10.18926/14053 |
|---|---|
| FullText URL | Mem_Fac_Eng_OU_42_1.pdf |
| Author | Asatani Jun| Koumoto, Takuya| Toru Fujiwara| Tadao Kasami| |
| Abstract | Two typical examples, the (32, 21, 6) and (64, 45, 8) extended code of primitive permuted BCH codes, are considered. The sets of minimum weight codewords are analyzed in terms of Boolean polynomial representation. They are classied by using their split weight structure with respect to the left and right half trellis sections, and for each class, the standard form is presented. Based on the results, we can generate a proper list of the minimum weight codewords of the codes. |
| Keywords | Boolean polynomial representation extended BCH codes minimum weight codewords binary shift invariance property |
| Publication Title | Memoirs of the Faculty of Engineering, Okayama University |
| Published Date | 2008-01 |
| Volume | volume42 |
| Issue | issue1 |
| Start Page | 1 |
| End Page | 9 |
| ISSN | 0475-0071 |
| language | 英語 |
| File Version | publisher |
| NAID | 120002308333 |
| JaLCDOI | 10.18926/14055 |
|---|---|
| FullText URL | Mem_Fac_Eng_OU_42_10.pdf |
| Author | Kanatani, Kenichi| |
| Abstract | The author introduced the "geometric AIC" and the "geometric MDL" as model selection criteria for geometric fitting problems. These correspond to Akaike’s "AIC" and Rissanen's "BIC", respectively, well known in the statistical estimation framework. Another criterion well known is Schwarz’ "BIC", but its counterpart for geometric fitting has been unknown. This paper introduces the corresponding criterion, which we call the "geometric BIC", and shows that it is of the same form as the geometric MDL. We present the underlying logical reasoning of Bayesian estimation. |
| Publication Title | Memoirs of the Faculty of Engineering, Okayama University |
| Published Date | 2008-01 |
| Volume | volume42 |
| Issue | issue1 |
| Start Page | 10 |
| End Page | 17 |
| ISSN | 0475-0071 |
| language | 英語 |
| File Version | publisher |
| NAID | 120002308447 |
| JaLCDOI | 10.18926/14056 |
|---|---|
| FullText URL | Mem_Fac_Eng_OU_42_18.pdf |
| Author | Kanatani, Kenichi| Yasuyuki Sugaya| |
| Abstract | We classify and review existing algorithms for computing the fundamental matrix from point correspondences and propose new effective schemes: 7-parameter Levenberg-Marquardt (LM) search, EFNS, and EFNS-based bundle adjustment. Doing experimental comparison, we show that EFNS and the 7-parameter LM search exhibit the best performance and that additional bundle adjustment does not increase the accuracy to any noticeable degree. |
| Publication Title | Memoirs of the Faculty of Engineering, Okayama University |
| Published Date | 2008-01 |
| Volume | volume42 |
| Issue | issue1 |
| Start Page | 18 |
| End Page | 35 |
| ISSN | 0475-0071 |
| language | 英語 |
| File Version | publisher |
| NAID | 120002308468 |
| JaLCDOI | 10.18926/17843 |
|---|---|
| FullText URL | Mem_Fac_Eng_OU_43_61.pdf |
| Author | Kawamura, Mao| Konishi, Masami| Yamagata, Katuki| Shimomura, Koichi| |
| Abstract | In this research, a Human Interface system is designed intended to mobile crane. The intervention of human is unavoidable to attain the high performance of electro mechanical system. As is known, crane operation is complicated. Recently, the decrease of expert person induced crane accident. So in near future, it is required a partial automation of crane operation and human support technology. We are aiming at the development of the operation support system for a crane. In this research, development of the hydro mechanical models representing both of static and dynamics movements are made. Further, actual experimental data of operating mobile crane, which are electrical signal data and three-dimension (3D) position of moving load is measured. The actual operating data are compared with the model and it is found that the developed electromechanical model can explain the behaviors of actual data. |
| Publication Title | Memoirs of the Faculty of Engineering, Okayama University |
| Published Date | 2009-01 |
| Volume | volume43 |
| Start Page | 61 |
| End Page | 74 |
| ISSN | 1349-6115 |
| language | 英語 |
| File Version | publisher |
| NAID | 120002308930 |
| JaLCDOI | 10.18926/17829 |
|---|---|
| FullText URL | Mem_Fac_Eng_OU_43_16.pdf |
| Author | Kurose Tomoyuki| Tsuruta, Kenji| Totsuji, Chieko| Totsuji, Hiroo| |
| Abstract | The finite-difference time-domain (FDTD) method has been applied to the calculation of the phonon band structure of two-dimensional (2D) phononic crystals, consisting of metal cylinders placed periodically in liquid. By comparing several combinations of materials for metal cylinder and liquid, we analyze the dependence of the band structures on sound speed and density of liquid media. Moreover, the negative refraction of the acoustic waves is observed at the interfaces between phononic crystal slab and the liquid. We find that an acoustic“lens effect”with the slab appears due to the negative refractions. The relationship between the focal intensity in the lens effect and the band structure is discussed. |
| Publication Title | Memoirs of the Faculty of Engineering, Okayama University |
| Published Date | 2009-01 |
| Volume | volume43 |
| Start Page | 16 |
| End Page | 21 |
| ISSN | 1349-6115 |
| language | 英語 |
| File Version | publisher |
| NAID | 120002308928 |
| JaLCDOI | 10.18926/17833 |
|---|---|
| FullText URL | Mem_Fac_Eng_OU_43_27.pdf |
| Author | Totsuji, Hiroo| |
| Abstract | When the Coulomb coupling between fine particles becomes sufficiently strong in fine particle plasmas, the isothermal compressibility of the whole system diverges and we have a phase separation and an associated critical point. Experimental conditions of fine particle plasmas, densities and temperatures of components and the fine particle size, are obtained corresponding to characteristic parameters around the critical point and the dependency on ion species and other factors is discussed. |
| Publication Title | Memoirs of the Faculty of Engineering, Okayama University |
| Published Date | 2009-01 |
| Volume | volume43 |
| Start Page | 27 |
| End Page | 31 |
| ISSN | 1349-6115 |
| language | 英語 |
| File Version | publisher |
| NAID | 120002308947 |
| JaLCDOI | 10.18926/17847 |
|---|---|
| FullText URL | Mem_Fac_Eng_OU_43_93.pdf |
| Author | Ueno, Hirokazu| Morikawa, Yoshitaka| |
| Abstract | This paper investigates the relation between error distribution and predictive order of minimum mean abusolute error predictors (MMAE predictors) designed for lossless coding of grayscale images. Design of MMAE predictors reduces to the linear programming problem. Let k be the number of coefficients in a predictor (predictor order), we imagine that predictor order k may have a distribution shaping effect. Main purpose of this paper is to ensure that k has such an effect. |
| Publication Title | Memoirs of the Faculty of Engineering, Okayama University |
| Published Date | 2009-01 |
| Volume | volume43 |
| Start Page | 93 |
| End Page | 98 |
| ISSN | 1349-6115 |
| language | 英語 |
| File Version | publisher |
| NAID | 120002308979 |
| JaLCDOI | 10.18926/17841 |
|---|---|
| FullText URL | Mem_Fac_Eng_OU_43_55.pdf |
| Author | Inoue, Shinichiro| Konishi, Masami| Imai, Jun| |
| Abstract | In this research, an image processing method and a system for inspection support of a rod figured cutting tool are developed. As is well known, the visual inspection of a cutting tool by image processing is not easy, because cutting blade have a helical blade structure. To cope with the problem, an experimental facility with rotation and longitudinal tool shift functions to enable acquisition of blade surface pictures along a cutting rod is developed. The type of the defect treated in this paper is the spot of coating on blade surface. To judge the quality of the processed image of blade surface, neural network with autonomous learning is used. The processed image of cutting tool is divided into 64 × 64 blocks used for the input to the neural networks. Before input, each block data is preprocessed applying a edge detection filter and a transformation by the discrete fourier transform (DFT). Using these technologies, the experimental inspection system is built and tested to check the capabilities of the inspection algorithms. The diagnostic performance of the surface defect of a cutting tool was confirmed. There remained a problem to mis judge the normal tools as the defect. |
| Publication Title | Memoirs of the Faculty of Engineering, Okayama University |
| Published Date | 2009-01 |
| Volume | volume43 |
| Start Page | 55 |
| End Page | 60 |
| ISSN | 1349-6115 |
| language | 英語 |
| File Version | publisher |
| NAID | 120002308973 |
| JaLCDOI | 10.18926/17853 |
|---|---|
| FullText URL | Mem_Fac_Eng_OU_43_113.pdf |
| Author | Sakemi, Yumi| Kato, hidehiro| Nogami, Yasuyuki| Morikawa, Yoshikawa| |
| Abstract | Barreto–Naehrig (BN) curve has been introduced as an efficient pairing-friendly elliptic curve over prime field F(p) whose embedding degree is 12. The characteristic and Frobenius trace are given as polynomials of integer variable X. The authors proposed an improvement of Miller's algorithm of twisted Ate pairing with BN curve by applying X of small hamming weight in ITC–CSCC2008; however, its cost evaluation has not been explicitly shown. This paper shows the detail of the cost evaluation. |
| Publication Title | Memoirs of the Faculty of Engineering, Okayama University |
| Published Date | 2009-01 |
| Volume | volume43 |
| Start Page | 113 |
| End Page | 116 |
| ISSN | 1349-6115 |
| language | 英語 |
| File Version | publisher |
| NAID | 120002308945 |
| JaLCDOI | 10.18926/17851 |
|---|---|
| FullText URL | Mem_Fac_Eng_OU_43_108.pdf |
| Author | Nekado, Kenta| Kato, Hidehiro| Nogami, Yasuyuki| Morikawa, Yoshitaka| |
| Abstract | Recently, pairing-based cryptographies such as ID-based cryptography and group signature have been studied. For fast pairing calculation, not only pairing algorithms but also arithmetic operations in extension field must be efficiently carried out. The authors show efficient arithmetic operations of extension field for Xate pairing especially with Freeman curve. |
| Publication Title | Memoirs of the Faculty of Engineering, Okayama University |
| Published Date | 2009-01 |
| Volume | volume43 |
| Start Page | 108 |
| End Page | 112 |
| ISSN | 1349-6115 |
| language | 英語 |
| File Version | publisher |
| NAID | 120002308904 |
| JaLCDOI | 10.18926/17849 |
|---|---|
| FullText URL | Mem_Fac_Eng_OU_43_99.pdf |
| Author | Kato, Hidehiro| Nogami, Yasuyuki| Morikawa, Yoshitaka| |
| Abstract | A square root (SQRT) algorithm in extension field F(p(m))(m = r(0)r(1)･･･r(n−1)･2(d), r(i) : odd prime, d : positive integer) is proposed in this paper. First, a conventional SQRT algorithm, the Tonelli-Shanks algorithm, is modified to compute the inverse SQRT in F(p(2d)), where most of the computations are performed in the corresponding subfields F(p(2i)) for 0 ≤ i ≤ d-1. Then the Frobenius mappings with addition chain are adopted for the proposed SQRT algorithm, in which a lot of computations in a given extension field F(p(m)) are also reduced to those in a proper subfield by the norm computations. Those reductions of the field degree increase efficiency in the SQRT implementation. The Tonelli-Shanks algorithm and the proposed algorithm in F(p(6)) and F(p(10)) were implemented on a Core2 (2.66 GHz) using the C++ programming language. The computer simulations showed that, on average, the proposed algorithm accelerated the SQRT computation by 6 times in F(p(6)), and by 10 times in F(p(10)), compared to the Tonelli-Shanks algorithm. |
| Publication Title | Memoirs of the Faculty of Engineering, Okayama University |
| Published Date | 2009-01 |
| Volume | volume43 |
| Start Page | 99 |
| End Page | 107 |
| ISSN | 1349-6115 |
| language | 英語 |
| File Version | publisher |
| NAID | 120002308980 |
