JaLCDOI 10.18926/15398
フルテキストURL Mem_Fac_Eng_OU_27_1_93.pdf
著者 西垣 誠| Sudinda Teddy| Hishiya Tomoyuki| 河野 伊一郎|
抄録 In this paper the author will be describe phenomena of advection dispersion in subsurface flow by using Eulerian Lagrangian Finite Element Method. Where Finite Element Method with Galerkin formulation and weigthed residual method is used to solve seepage and advection dispersion equation. The problem of one dimensional and two dimensional rectangular wave are analyzed in this paper. And the result of numerical analyses will be compared with analytical solutions. The numerical results showed the very good agreement with the analytical solutions.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1992-11-25
27巻
1号
開始ページ 93
終了ページ 105
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307768
JaLCDOI 10.18926/15399
フルテキストURL Mem_Fac_Eng_OU_27_2_1.pdf
著者 梶原 康博| 大崎 紘一|
抄録 Precedence relation in assembly has been determined by experience only. Now, an expert system is developed for determining such precedence relation. The conjugate states of the units of a product are shown in face frames and unit frames following the frame model. Seven rules are formulated. They consider geometrical interference of units, and make the precedence relation enable operation time to be shorter, and the number of JIG and substandards to be smaller. These rules are programized by computer language(PROLOG).
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1993-03-25
27巻
2号
開始ページ 1
終了ページ 9
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307210
JaLCDOI 10.18926/15400
フルテキストURL Mem_Fac_Eng_OU_27_2_11.pdf
著者 岡 久雄| 山本 辰馬| Saratani Keiji| Tanaka Masahiro| Kawazoe Takayoshi|
抄録 The use of dental implants has increased together with increases in the human life span and it has become an imperative subject for dentists to familiarize themselves with this treatment modality. Unfortunately, there has been no practical and quantitative method for in vivo evaluation of the stability of dental implants. In the tooth mobility examination, the tactile sense of natural teeth is different from that of dental implants. The authors have developed an automatic diagnosis system of tooth mobility for clinical use. The biomechanical mobility of peri-implantium is measured with a pseudo-random vibration, from which the viscoelasticity c1, c2, k of peri-implantium is obtained. The diagnosis system has been applied to the quantitative evaluation of the stability of implants : endodontics endosseous implants (titanium pin), endosseous implants (Bioceram). It has also been applied to the evaluation of the long-term prognoses of dental implantation (Bioceram) and the examination of Intramobile implant (IMZ), and the satisfactory results have been obtained.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1993-03-25
27巻
2号
開始ページ 11
終了ページ 17
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002308018
JaLCDOI 10.18926/15401
フルテキストURL Mem_Fac_Eng_OU_30_2_21.pdf
著者 Tachibana Hiroyuki| 東辻 浩夫|
抄録 In order to apply quantum waveguides to electronic devices, we calculate the electrostatic potential in the split-gate quantum wire and establish the relation between the electrostatic potential and the square well potential which is usually assumed in simulations of these waveguides. The height and width of the square well potential are expressed as simple functions of the gate voltage and their dependencies are clarified. The results may be useful in calculating the characteristics of electronic devices based on quantum waveguides as functions of controllable parameters such as gate voltage.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1996-03-29
30巻
2号
開始ページ 21
終了ページ 25
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307620
JaLCDOI 10.18926/15402
フルテキストURL Mem_Fac_Eng_OU_30_2_27.pdf
著者 東辻 浩夫| 岸本 篤也| 東辻 千枝子|
抄録 The behavior of the Yukawa system in external one-dimensional force fields is analyzed by the molecular dynamics simulation. The formation of layered structures at low temperatures is observed and the relation between the number of layers and characteristic parameters of the system is obtained. Since the Yukawa system serves as a model of clouds of dust particles in plasmas (dusty plasma) which play an important role in plasma processes of semiconductor engineering, the results may be useful to control the quality of semiconductor wafers in such processes. In simulations, periodic boundary conditions are imposed in two dimensions and deformations of periodic boundaries are allowed in order to reduce the effect of boundaries without giving too much constraint on the symmetry.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1996-03-29
30巻
2号
開始ページ 27
終了ページ 37
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307582
JaLCDOI 10.18926/15403
フルテキストURL Mem_Fac_Eng_OU_27_2_19.pdf
著者 奈良 重俊| 東辻 浩夫|
抄録 Numerical simulations of a single layer recurrent neural network model in which the synaptic connection matrix is formed by summing cyclic products of succesive patterns show that complex dynamics can occur with the reduction of a connectivity parameter which is the number of connection between neurons. The structure in these dynamics is discussed from the viewpoint of realizing complex function using complex dynamics.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1993-03-25
27巻
2号
開始ページ 19
終了ページ 40
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307451
JaLCDOI 10.18926/15404
フルテキストURL Mem_Fac_Eng_OU_27_2_41.pdf
著者 Prokop Jiri| Myojin Sho|
抄録 The fundamental objective of this paper is to aggregate and establish a set of practical principles, guidelines, and procedures to clarify and improve classification yard design and to enhance the efficiency of the design process. The paper primarily addresses theoretical and technical aspects of hump yard height and grade design, placement of the switches and the retarders. It attempts to compile and document yard design procedures, based on the Theory of Energy Head and Energy Loss. This procedures are applicable to the design of new yards, rehabilitation of the existing yards of different types and sizes including manually operated as well as highly automated classification yards.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1993-03-25
27巻
2号
開始ページ 41
終了ページ 58
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307241
JaLCDOI 10.18926/15405
フルテキストURL Mem_Fac_Eng_OU_30_2_39.pdf
著者 東辻 千枝子|
抄録 A simple model for oxygen ion conduction in perovskite compounds is proposed. The potential for an oxygen ion is calculated as the sum of the long range Coulomb potential and short range repulsive potential in a cubic lattice. The activation energy is estimated as the difference in the values of potential at the barrier and at the stable site. When appropriate conditions are satisfied, the activation energy has a minimum as a function of lattice constant in accordance with recent experiments.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1996-03-29
30巻
2号
開始ページ 39
終了ページ 43
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307769
JaLCDOI 10.18926/15406
フルテキストURL Mem_Fac_Eng_OU_27_2_59.pdf
著者 Prokop Jiri| Myojin Sho|
抄録 The paper presents methods for simulation and examination of the performance of a classification yard, including both manual and computer-aided methods. Presented methods are applicable to the simulation and examination of full range of yards of different types and sizes including manually operated as well as highly automated classification yards.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1993-03-25
27巻
2号
開始ページ 59
終了ページ 71
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307384
JaLCDOI 10.18926/15407
フルテキストURL Mem_Fac_Eng_OU_26_1_1.pdf
著者 榊原 精| Kanadani, Teruto|
抄録 Reversion of the age-hardened Al-15mass % Zn alloy, in which ellipsoidal GP zones were formed, was investigated by hardness test. Ellipsoidal zones were reverted more quickly near the surface and grain boundary than in the interior, as spherical zones did. The results confirm their role as sources for vacancies in reversion.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1991-11-30
26巻
1号
開始ページ 1
終了ページ 7
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002308003
JaLCDOI 10.18926/15408
フルテキストURL Mem_Fac_Eng_OU_29_2_1.pdf
著者 榊原 精| Nakagawa, Keiyu| Kanadani, Teruto|
抄録 Effect of addition of a small amount of copper to Al- 12mass % Zn binary alloy on the process of low temperature aging is studied by hardness test and transmission electron microscopy. Age hardening rate after quenching from various temperatures is slowed down by addition of 0.5mass % copper to the binary alloy. The hardness obtained after long aging, however, is increased a little by the addition of copper. The extent of soft surface layer formed by aging in the copper-added alloy is nearly equal to that obtained in the binary alloy.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1995-03-27
29巻
2号
開始ページ 1
終了ページ 4
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307763
JaLCDOI 10.18926/15409
フルテキストURL Mem_Fac_Eng_OU_29_2_5.pdf
著者 稲葉 英男| Tu Ping| 尾崎 公一|
抄録 Transient characteristics of the rectangular latent heat storage vessel packed with shape-stabilized phase change (solid-liquid) material (PCM) are investigated numerically by solving the governing equations of both the PCM and the heat transfer medium(water) simultaneously as a conjugate problem with the finite difference technique. It's found that the heat storage characteristics are greatly affected by the flow direction of the heat transfer medium since the natural and forced convection coexists in the heat storage vessel. That is, it is classified that the effectively thermal efficiency of the latent heat storage system is obtained by the downflow along vertical PCM for heat storage process and the upflow for heat release process. The effect of the inlet velocity of heat transfer medium(water) on transient heat characteristics of the latent heat storage system is also revealed in the present study.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1995-03-27
29巻
2号
開始ページ 5
終了ページ 12
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307377
JaLCDOI 10.18926/15410
フルテキストURL Mem_Fac_Eng_OU_26_1_9.pdf
著者 Uno, Yoshiyuki| Nakajima, Toshikatsu| Okada Minoru|
抄録 Practical utilization of ram type electrical discharge machining in uninflammable fluid has been expected in place of inflammable kerosine type fluid for unmanned operation in a workshop. The electrical discharge machining performance in deionized water is experimentally investigated on the basis of the analysis of the crater generated by a single pulse discharge. The experimental analysis makes it clear that the electrical discharge machining performance in deionized water is greatly affected by the electrode polarity. The metal removal rate in the normal polarity machining is higher than that in reverse polarity machining, while the electrode wear rate in the normal polarity machining is greater than that in reverse polarity machining. Therefore the electrode polarity should be properly selected according to the purpose of machining.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1991-11-30
26巻
1号
開始ページ 9
終了ページ 20
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307319
JaLCDOI 10.18926/15411
フルテキストURL Mem_Fac_Eng_OU_29_2_13.pdf
著者 Dwianto Gatot| 大崎 紘一| 梶原 康博|
抄録 We propose a method to design the supplying method of parts to an assembly line. Three types of supplying model (Serial, Parallel, and Mixed) are proposed based on the relation between the area of part and that of the transportation equipment. The part is supplied by the pallet on which the all parts of one product are arranged or by the lot of one part. AGV or conveyor are used to transport the pallet. The supplying model is evaluated from the total transportation cost calculated from the price of the transportation equipment and of land.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1995-03-27
29巻
2号
開始ページ 13
終了ページ 21
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307903
JaLCDOI 10.18926/15412
フルテキストURL Mem_Fac_Eng_OU_26_1_21.pdf
著者 野津 滋| 稲葉 英男|
抄録 A numerical study is performed for the facilitated diffusion of carbon-dioxide in an ultrapure water film flowing downward along a vertical surface. The model adopted for the present work includes the effects of the reaction rate for the hydration of CO(2)in a liquid. Comparison of the total concentration of CO(2) for different film thickness indicates that the effects of the hydration is more remarkable for the thinner liquid film.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1991-11-30
26巻
1号
開始ページ 21
終了ページ 26
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307958
JaLCDOI 10.18926/15413
フルテキストURL Mem_Fac_Eng_OU_29_2_23.pdf
著者 梶原 康博| 大崎 紘一| Dong Rui|
抄録 A method for reducing the variety of parts is proposed. The variety of parts in a product and the variety of parts among products are evaluated in consideration of some factors that influence the production cost. Rules are formulated for selecting parts which should be eliminated or whose designs should be changed to reduce these varieties. An expert system is developed based on this method for reducing the variety of parts.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1995-03-27
29巻
2号
開始ページ 23
終了ページ 27
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307257
JaLCDOI 10.18926/15414
フルテキストURL Mem_Fac_Eng_OU_26_1_27.pdf
著者 冨田 栄二| Nsunge Felix Chintu| 浜本 嘉輔|
抄録 Distributions of hydrogen gas concentration in a suddenly started, single shot hydrogen gas jet issuing from a 1 mm diameter injector into still air were measured using laser interferometry method. This unsteady, turbulent free jet flow has also been calculated using the two-equation, high Reynolds number version of k-ε turbulence model and hybrid scheme for treating combined diffusion and convection in the SIMPLE algorithm. The injection pressure was 0.5 MPa for which predicted and measured temporal jet tip penetration distributions indicate that the jet discharged into still air at Mach 0.25. The level of agreement between present prediction and measurement is good in some regions and poor in others.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1991-11-30
26巻
1号
開始ページ 27
終了ページ 41
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307648
JaLCDOI 10.18926/15415
フルテキストURL Mem_Fac_Eng_OU_29_2_29.pdf
著者 岡 久雄| 福田 敬|
抄録 In the stiffness evaluation from the skin surface, the body structure under the skin, like a bone and muscle, influences on the measurement results. The authors developed the measurement system of biomechanical impedance with applying a vibration of acoustic frequency onto the body surface. We measured the viscoelasticity of the silicone-gel model, which involves metal blocks, from the gel surface by using this system. The internal structure of model is estimated from the relation between the viscoelasticity and the distance from the gel surface to the internal block. Applying this method, the shape of ribs of the right chest are estimated. The shapes and viscoelasticity of silicone-gel tumor model, which has two different tumors, are also estimated.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1995-03-27
29巻
2号
開始ページ 29
終了ページ 37
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307199
JaLCDOI 10.18926/15416
フルテキストURL Mem_Fac_Eng_OU_26_1_43.pdf
著者 Bouzidi, Moncef| 古賀 隆治| 和田 修己| 香川 直己| Hai Xu| 小坂 恵| Sano HIroya|
抄録 A numerical technique called as "adjoint spectrum" has been proposed by the authors in a previous work. Two applications of it are presented here. It is demonstrated that by generalizing the aspect of adjoint spectrum it becomes possible to measure densities of mixed gases simultaneously. An experimental proof of this has been carried on and simultaneous measurement of densities of both methane and dinitrogen oxide was realized. On the other hand, it is also reported that frequency shifting of spectra, which is a cause of error in spectrometric measurements, can be corrected by exploiting the adjoint spectrum technique in connection with the Taylor expansion. Numerical examples showing the success of this method are reported as well.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1991-11-30
26巻
1号
開始ページ 43
終了ページ 49
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307796
JaLCDOI 10.18926/15417
フルテキストURL Mem_Fac_Eng_OU_29_2_39.pdf
著者 岡 久雄| 坂本 俊哉| Irie Takashi|
抄録 The body structures under the skin surface, such as bones and tendon, have an influence on the stiffness evaluation observed from the surface. In this case, the observed stiffness should be called an apparent stiffness. To obtain the biomechanical properties of skin itself, the influence of body structure should be removed. This study deals with the correction method of apparent viscoelasticity which calculated from apparent biomechanical impedance. This method is applied to the measured result of the forearm and the right chest to confirm its effectiveness.
出版物タイトル Memoirs of the Faculty of Engineering, Okayama University
発行日 1995-03-27
29巻
2号
開始ページ 39
終了ページ 47
ISSN 0475-0071
言語 English
論文のバージョン publisher
NAID 120002307527